湖北国能优泰电力有限公司
分享到：
10kV 600A T2T型接头
600A T2T Bol deadbreak connector
-
T2T-15/600
产品应用：
10kV 600A T2T型接头采用高品质的绝缘橡胶制成,为全绝缘、全密封螺栓连接式终端电缆接头。产品为600A T型电缆接头和负荷转换头的组合。广泛应用于户外美式箱变，开关柜，美式电缆分接箱，地埋式变压器及其它电气设备的连接。安装在600A母排接口上及美式箱变的600A套管上。负荷转换头实现600A转为200A回路与200A肘型电缆接头或肘型避雷器连接。测试点可安装带电显示器或故障指示器，以便查询设备带电状态和故障状态。
10kV 600A T2T bol deadbreak connector adopt high quality insulation rubber,fully-insulated,fully sealed.It is the combination for 600A T type cable connector and loadbreak bushing extender. widely used in outdoor american pad-mound transformer, switch cabinet,american cable branch box, buried transformer and other electrical equipment connection.installed in 600A busbar and 600A bushing of american pad-mound transformer. loadbreak bushing extender can achieve 600A turn into 200A loop,and connected with 200A elbow cable connector or elbow arrester. test point can installed charged display or fault indicator, so that to check equipment charged status and fault status。
包装标准：
T型接头本体、负荷转换头
压接端子、应力锥
内六角扳手
双头螺栓、安装工具
铜接地线、硅脂、清洁纸
安装标尺卡、产品合格证
安装指导说明书
T-body, conversion head
Crimp terminal, cable adaptor
Inner hexagon spanner
Two-head screw,install tools
Copper grounding wire, silicon grease, cleaning paper
Install scale card, product information
Instruction manual
10kV 600A T2T型接头采用高品质的绝缘橡胶制成,为全绝缘、全密封螺栓连接式终端电缆接头。产品为600A T型电缆接头和负荷转换头的组合。广泛应用于户外美式箱变，开关柜，美式电缆分接箱，地埋式变压器及其它电气设备的连接。安装在600A母排接口上及美式箱变的600A套管上。负荷转换头实现600A转为200A回路与200A肘型电缆接头或肘型避雷器连接。测试点可安装带电显示器或故障指示器，以便查询设备带电状态和故障状态。
10kV 600A T2T bol deadbreak connector adopt high quality insulation rubber,fully-insulated,fully sealed.It is the combination for 600A T type cable connector and loadbreak bushing extender. widely used in outdoor american pad-mound transformer, switch cabinet,american cable branch box, buried transformer and other electrical equipment connection.installed in 600A busbar and 600A bushing of american pad-mound transformer. loadbreak bushing extender can achieve 600A turn into 200A loop,and connected with 200A elbow cable connector or elbow arrester. test point can installed charged display or fault indicator, so that to check equipment charged status and fault status。
包装标准：
T型接头本体、负荷转换头
压接端子、应力锥
内六角扳手
双头螺栓、安装工具
铜接地线、硅脂、清洁纸
安装标尺卡、产品合格证
安装指导说明书
T-body, conversion head
Crimp terminal, cable adaptor
Inner hexagon spanner
Two-head screw,install tools
Copper grounding wire, silicon grease, cleaning paper
Install scale card, product information
Instruction manual